SORRY FOR THE LOW VOLUME, HEADPHONES MAY HELP. Part 1 of How to build your own carpet mill/tread mill. This is a step by step how to with a finished product.
Great way to condition your dog, i dont care why you want him conditioned, and i dont wanna hear any bs about for fighting blah,blah. Like and comment below to let me know how i did.
I'm making a cobra meal treadmill for my Dog pill and then I made one before I Looked around on YouTube a little bit I Mean there's really nothing on there so I figured I just do my own I make the Video help somebody else I was trying to Figure out how to build I want to build One for a dog this kind of overview of The floor how it's going to be will have These rollers on the end this is just For support and that I got is a piece of Paneling but it's a slick on top kind of Like a dry erase board and that's what's Gonna be on top of here and I got these I made it five feet by two and a half Feet for that'd be plenty wide enough Long enough and this right here is just Four inch PVC pipe and I got a landscape Timber inside of it to drill tube and Hold two and no I got this piece of 3/8 When conduit nipple this is what I'm Going to use for my bearings inside of The plywood and I've got these lag bolts To go in the PVC pipe and then through Here it's being on This legs just going to be bottom and Top in any pot on it like I cut just Like six inches at 18 inches I've got These three feet and when you use this For baking my staying with first caller I said I already cut all this but uh I Got to drill my holes for the barrier to Spin on and then these a PVC pipe but Already marked already
Not already more to all this but I mean Thomas since it's four and a half inches Wide so it'll be two and a quarter mark That way in this way find the center Over do that on both ends on both these Pieces and then right here I wanted I Wanted to have some overhang right here So the guys the carpet is going in and Up then I'll take a like yeah two and a Half inches and then I measure back two And a quarter off that line because That's how thickest was how's my center Mark which is right here and then I Measure the width it is it's a it's one At five-eighths this way and then for an Eleven sixteenths off the hand right Here that's where I'm at my Center and I Mark all these pieces already I marked My landscape timbers so I got to drill My holes in them I got got a 5/8 bit for This it's three-eighths but I'm going to Water it out a little bit but I want to Get tight so we don't move that this 5/16 bit to drilling landscape timbers Which is smaller because I feel like Sitting there cooking this all day Trying to give me the landscape dinner They know this one won't screw in there Won't drill it out first line pilot hole Roughing screwing in easy what I'm going To do that will come back all right well I'll drill my holes right here on the Sides and drill pilot holes and these Landscape timbers and then I cut the
Nipples put inside – before put them you try to water them Out a little bit so you're good All right this is same bet these washers Because it fit a little bit it will be Loose want to move around too much and That's where the head of the boat so I Got splat washing for that you screw These in here Although that make sure that this right Here on the boat isn't threaded because If it is it's not going to spin in this Stuff ready so this little nipple who You know I'm in the metal piece oh I Guess I still would if it's small enough For it I wonder smooth there wouldn't be No friction you don't want too tight so You can build a spin more freely Back it up a little bit So you want to get me a little bit of a Gap so there's a roll it's not my role Is to be dragging on that day before Whole was a little bit crooked if you Are Should have the same amount sticking out On both sides here got a sinner will do These other ones and then come back sit Here and watch me turn squeeze all day All right putting these on and this Ropes talking right like adjusting it You don't want to keep snow going here Get it tightening backing off a little Bit shake it see how thrown it gets Pretty good am i back rock
Slap don't get off Loosen both sides This could that's great when I have a Problem See I didn't finish doing this with some Of these is complete The pilot oh that should go in pretty Even you know these boats that I got I Think the road like three eighths by Like six inches long and then the gap Owner right there was in the width of a 2×4 see I tightened it all the way down Anyway thanks for uh on these landscape Timbers it probably would have helped Devoted did it before I put the lag Bolts in but you got to put some screws In it So keep the landscapes timber from Slipping inside the PVC pipe I mean the Screws I'm using on everything three and A half inch wood screws someone to do That when the easier gotta find the top Of it so I would have been easier And follow that down or something a Little bit they're like taking about no More all right so here's the top of the Landscape Tim that's how supposed to go In I don't know why this Okay I don't know what happened there And we'll put two more of those Probably be easier with a cordless drill – but it's what I've got so I'm using All right do the same thing on those Guys
Besides rolling good that one might cut A little bit off that PVC pipe bro Hanging on one spot dudes go home Well are you
